1. Master the construction drawings of the cleaning room, carefully check the plane design drawing of color steel plate, node requirements, the relationship between color steel plate and construction engineering, the color tone, filler and basic specification and model requirements of color steel plate, the specification and model and reasonable layout of doors and windows in the background wall of color steel plate decoration, the way of auxiliary materials and other ominous contents.

2.二次排板制图,它是彩钢板预制件构件和安裝的一步，是把设计图纸变换为可供在加工厂次生产制造，把标准型号规格板制成不一样类型的墙板，进行构成以体现设计意图的中间变换图，并在彩钢板加工厂生产加工出标准板材，在施工工地拼装，即可以保证墙板的牢固水准又可以加快彩钢板的安装速度。

2. Secondary plate layout drawing is a step for prefabricated components and installation of color steel plate. It is to transform the design drawing into an intermediate transformation drawing for secondary production and manufacturing in the processing plant, make standard model and specification plates into different types of wall plates, form them to reflect the design intention, produce and process standard plates in the color steel plate processing plant, and assemble them at the construction site, It can not only ensure the firm level of wall panels, but also accelerate the installation speed of color steel plates.

3.在清洁室加工厂预制件构件时，根据工作经历，门页、门扇和缝间充分考虑到间隙和安裝容积。并在所有运输制作，安装整个过程中，防止划伤、工作压力及表面撞击，以防止出现无法较正的凹坑和划痕。

3. When processing prefabricated components in the factory in the cleaning room, according to the work experience, the gap and installation volume between the door leaf, door leaf and joint shall be fully considered. During the whole process of transportation, fabrication and installation, scratches, working pressure and surface impact shall be prevented to prevent pits and scratches that cannot be straightened.

4.清洁室彩钢板安装前的测量放线工作上，应在地(楼)面开展后进行，并在具备安装的别的相关规范如非常大机械设备已运到位、暗埋地面管路已调整完及性夹层安装工作上基本开展，才可以进行。

4. The measurement and setting out before the installation of color steel plate in the cleaning room shall be carried out after the ground (floor) surface, and can only be carried out after other relevant specifications for installation are available, such as the transportation of very large mechanical equipment in place, the adjustment of buried ground pipeline and the installation of sexual interlayer.

5.装上下马槽，下码槽一般采用带有內外R角的铝合金型材。用射钉固定不变于地面所绘的在网上，射钉的位置以直线1.2-1.5m间距，转角及智能终端距边0.1米为宜，采用橡胶止水带橡胶材料条的在射钉之前把二根窗户密封条放入槽下，在射钉固定不变后造成防水防护密闭式。

5. The upper and lower grooves with aluminum profile R are generally installed. Fixed on the net drawn on the ground with shooting nails, the position of shooting nails should be 1.2-1.5m away from the straight line, and the corner and intelligent terminal should be 0.1M away from the edge. If rubber waterstop rubber material strip is used, put two window sealing strips under the groove before shooting nails, and form a waterproof protection closed type after the shooting nails are fixed.

6.细立墙板，分配版图放进预制件构件好的构件，构件间以固定不变软件锁住相邻墙板。应特别注意的是在组塔墙板的此外互相配合好电器设备暗埋管路及箱盒。

6. Fine vertical wallboard, distribution layout, put into the prefabricated components, and lock the adjacent wallboards with fixed software between the components. It should be noted that in addition to the wall plate of the tower, the concealed buried pipelines and boxes of electrical equipment should be matched with each other.

7.装清洁室装修吊顶板：现浇板的净重量支点是依据固定不变在周边的底梁及中间悬吊训练训炼的T型铝。长边缝间依据固定不变固定不变和工程加固

7. Installation of ceiling plate for cleaning room decoration: the net weight fulcrum of cast-in-situ plate is based on the T-shaped aluminum suspended and trained in the surrounding bottom beam and the middle. The long side joints shall be fixed and reinforced according to the engineering