热门关键词:济南彩钢板 | 济南复合板 | 济南彩钢瓦 | 济南c型钢 | 济南钢结构 |
新闻中心
联系我们
济南坚固彩钢工程公司
联系人:孙经理
电话:18963458998
地址:济南市工业北路81号北邻
济南彩钢板如何进行腐蚀处理?
来源:http://www.jnjgcg.com/ 日期:2020-07-07 发布人:
彩钢板是当下比较受推崇的新兴材料之一。随着科技的进步、环境意识的增强,人民生活水平的提高,彩钢板应用的范围越来越广泛,无论是建造简单的房屋还是使用可移动的板房,在房屋的屋顶上使用彩色瓷砖都是很普遍的,不仅便宜,而且易于制造。 长期风吹日晒,彩钢板很容易腐蚀,如果不及时处理,腐蚀只会越来越严重,从而影响彩钢板的使用。接下来济南彩钢板厂家就为大家详细介绍一下。
Color steel plate is one of the most popular emerging materials. With the progress of science and technology, the enhancement of environmental awareness, and the improvement of people's living standards, color steel plate is widely used. Whether it is to build a simple house or use a movable plank house, it is very common to use color tiles on the roof of the house, which is not only cheap, but also easy to manufacture. The color steel plate is easy to corrode if it is not treated in time, which will affect the use of color steel plate. Next, Jinan color steel plate manufacturers will give you a detailed introduction.
方法一:热浸锌处理。
Method one: hot dip zinc treatment.
热浸锌就是将除锈后的钢构件浸入600℃左右高温融化的锌液中,使彩钢板表面附着锌层,锌层厚度对5mm以下薄板不得小于65μm,对厚板不小于86μm,从而起到防腐蚀的目的。这种方法的优点是耐久年限长,生产工业化程度高,质量稳定。因而被大量用于受大气腐蚀较严重且不易维修的室外彩钢板中。如大量输电塔、通讯塔等。近年来大量出现的轻钢结构体系中的压型钢板等,也较多采用热浸锌防腐蚀。热浸锌的首道工序是酸洗除锈,然后是清洗。这两道工序不处理好会给防腐蚀留下隐患。对于济南彩钢板结构设计者,应该避免设计出具有相贴合面的构件,以免贴合面的缝隙中酸洗不干净或酸液洗不净。造成镀锌表面流黄水的现象。热浸锌是在高温下进行的。对于管形构件应该让其两端开敞。若两端封闭会造成管内空气膨胀而使封头板爆裂,从而造成事故通不畅,易在管内积存。
Hot dip galvanizing is to immerse the derusted steel member into the molten zinc solution at 600 ℃ to make the surface of color steel plate adhere to zinc layer. The thickness of zinc layer shall not be less than 65 μ m for thin plate less than 5mm and 86 μ m for thick plate, so as to achieve the purpose of anti-corrosion. The advantages of this method are long service life, high degree of industrialization and stable quality. Therefore, it is widely used in outdoor color steel plate which is seriously corroded by atmosphere and is not easy to maintain. Such as a large number of transmission towers, communication towers, etc. In recent years, hot dip galvanizing is widely used in profiled steel sheet of light steel structure system. The first process of hot dip galvanizing is pickling and derusting, and then cleaning. If these two processes are not handled properly, it will leave hidden danger for corrosion prevention. For the designers of Jinan color steel plate structure, it is necessary to avoid the design of components with joint surface, so as to avoid acid pickling or acid solution cleaning in the joints. The phenomenon of yellow water flowing on the surface of galvanized steel is caused. Hot dip galvanizing is carried out at high temperature. For tubular members, both ends should be open. If both ends are closed, the air in the pipe will expand and the head plate will burst, which will cause the safety accident to be blocked and easy to accumulate in the pipe.
方法二:热喷铝(锌)复合涂层。
Method two: thermal spraying aluminum (zinc) composite coating.
这是一种与热浸锌防腐蚀效果相当的长效防腐蚀方法。具体做法是先对济南彩钢板表面作喷砂除锈,使其表面露出金属光泽并打毛。再用乙炔-氧焰将不断送出的铝(锌)丝融化,并用压缩空气吹附到彩钢板表面,以形成蜂窝状的铝(锌)喷涂层(厚度约80μm-100μm)。然后用环氧树脂或氯丁橡胶漆等涂料填充毛细孔,以形成复合涂层。此法无法在管状构件的内壁施工,因而管状构件两端做气密性封闭,以使内壁不会腐蚀。这种工艺的优点是对构件尺寸适应性强,构件形状尺寸几乎不受限制。另一个优点则是这种工艺的热影响是局部的,受约束的,因而不会产生热变形。与热浸锌相比这种方法的工业化程度较低,喷砂喷铝(锌)的劳动强度化影响。
This is a long-term anti-corrosion method equivalent to hot-dip galvanizing. The specific method is to remove rust on the surface of Jinan color steel plate by sand blasting to expose metal luster and roughen the surface. Then the aluminum (zinc) wire continuously sent out is melted by acetylene oxygen flame, and then blown onto the surface of color steel plate with compressed air to form a honeycomb aluminum (zinc) spraying layer (thickness of about 80 μ M-100 μ m). Then, the pores are filled with epoxy resin or neoprene paint to form a composite coating. This method can not be used in the inner wall of the tubular member, so the two ends of the tubular component are sealed to prevent the inner wall from corrosion. The advantage of this process is that it has strong adaptability to the size of components, and the shape and size of components are almost unlimited. Another advantage is that the heat effect of this process is local and constrained, so it will not produce thermal deformation. Compared with hot-dip galvanizing, the industrialization degree of this method is lower, and the labor intensity of sand blasting aluminum (zinc) spraying is affected.
方法三:涂层法。
Method 3: coating method.
涂层法防腐蚀性一般不作为长效防腐蚀方法,所以用于室内彩钢板或相对易于维护的室外彩钢板较多。它一次成本低,但用于户外时维护成本较高。涂层法的施工时要先除锈,涂层依赖于除锈,所以要求高的涂层一般多用喷砂喷丸除锈,露出金属的光泽,除去所有的锈迹和油污。现场施工的涂层可用手工除锈。涂层的选择要考虑周围的环境。不同的涂层对不同的腐蚀条件有不同的耐受性。涂层一般有底漆(层)和面漆(层)之分。底漆含粉料多,基料少。成膜粗糙,与钢材粘附力强,与面漆结合性好。面漆则基料多,成膜有光泽,能保护底漆不受大气腐蚀,并能抗风化。不同的涂料之间有相容与否的问题,前后选用不同涂料时要注意它们的相容性。涂层的施工要有适当的温度(5~38℃之间)和湿度(相对湿度不大于85%)。涂层的施工环境粉尘要少,构件表面不能有结露。涂装后4小时之内不得淋雨。涂层一般做4~5遍。干漆膜总厚度室外工程为150μm,室内工程为125μm,允许偏差为25μm。在海边或海上或是在有强烈腐蚀性的大气中,干漆膜总厚度可加厚为200~220μm。
Coating method is not generally used as a long-term anti-corrosion method, so it is used for indoor color steel plate or outdoor color steel plate which is relatively easy to maintain. It has a low cost at one time, but it has a higher maintenance cost when used outdoors. During the construction of coating method, rust should be removed first, and the coating depends on rust removal. Therefore, the coating with high requirements is usually derusted by sandblasting and shot peening to expose the luster of metal and remove all rust and oil stains. The coating applied on site can be derusted by hand. The selection of coating should consider the surrounding environment. Different coatings have different resistance to different corrosion conditions. The coating is generally divided into primer (layer) and topcoat (layer). The primer contains more powder and less base material. The film is rough, has strong adhesion with steel and good adhesion with topcoat. The top coat has more base materials, glossy film, which can protect the primer from atmospheric corrosion and weathering. The compatibility of different coatings should be paid attention to when choosing different coatings. Proper temperature (5 ~ 38 ℃) and humidity (relative humidity no more than 85%) should be adopted for coating construction. The construction environment of coating should be less dust and there should be no condensation on the surface of components. No rain within 4 hours after painting. Coating is usually done 4 ~ 5 times. The total thickness of dry paint film is 150 μ m for outdoor engineering and 125 μ m for indoor engineering, and the allowable deviation is 25 μ M. The total thickness of dry paint film can be increased to 200 ~ 220 μ m on the sea or in the strong corrosive atmosphere.
以上就是今天为大家分享的关于济南彩钢板进行腐蚀处理的步骤的相关内容,希望对大家能有所帮助,想要了解更多内容可以电话联系我们或者关注我们的网站。
The above is today's sharing of Jinan color steel corrosion treatment steps related content, hope to help you, want to learn more can contact us by phone or pay attention to our website.
下一篇:济南复合板为何如此受人热捧? 上一篇:济南彩钢瓦在运输过程中产生的磨损
此文关键词: 济南彩钢板厂
阅读/ Recommended reading
- 济南彩钢板:屋顶太吵怎么办?坚固彩钢来帮助! 2024-11-21
- 济南复合板厂:复合板对人体有危害吗? 2024-11-20
- 济南彩钢板:哪种颜色更耐晒? 2024-11-18
- 济南彩钢板:彩钢板上做防水材料那种比较好? 2024-11-16
济南复合板厂:质量问题莫担忧
[2018-08-23]
复合板的质量通常取决于其制造材料和工艺。以下是一些关于复合板质量的信息: The quality of composite panels usually depends o...